![]() If you see the paper pick-up drums slip on the paper, then you may have better luck. Here's a written summary based on my experience: There are image and video instructions available from HP. Scenario 2: the pick-up drums do roll, but they slip on the paper Probably the entire printer must be torn down, and I don't expect you will be able to easily fix the excess play on the paper pick-up mechanism that drive the rubber rolls when pressed on the stack of paper. I suppose that because of excess play (programmed obsolescence?) eventually the cogwheels that drive the drums will slip. When the drums touch the paper, they simply don't rotate. When lifted, you will be able to rotate these drums in one direction. When printing, they are dropped to the top of the paper stack and will engage to separate the topmost sheet off the stack. When not printing, these drums are lifted. It looks like there is too much play in the paper pick-up unit (at the rightmost end inside the printer) on which both pick-up drums are mounted on a single arm. You most likely hear a grinding noise of plastic cogwheels slipping when the printer tries to feed a sheet of paper. Scenario 1: the pick-up drums do not roll, you hear a grinding noise Thanks much for steering me in the right direction. My printer had little use as I have a second one that I use for everyday printing, so, wanted to save the hp 310 as my good scanner/color/printer. Now works great! Hardest part was manipulating the dabbing of the epoxy on the spline due to working with mirror image. Waited until next morning to try printer. Very carefully slid the gear with fingers back on the shaft spline viewing that it was centered on the mating gear. Mixed some two part epoxy and carefully dabbed small amount on the shaft spline until about 100% coated. Then slid the gear down & off the spline. (can move the gear by hand back in line with the gear train and try once to see if it fixes problem). One small plastic gear slid off the steel shaft 'spline' not engaging drive train. Taped drop light to now top of printer looking at the mirror/gear train. Positioned small flat mirror angled on its edge to view gear train. follow the steps by selecting USB, plug the cable when the software guide you to do so and it will be reconfigured via a USB again.Stood hp 310a on its side. Once you are done, open the HP Photosmart 7520 software and click on Connect a new printer. If the specific desktop is not connected to a router at all or if you may prefer to keep it as USB anyway, open the Control Panel and select Devices and Printers (assuming it is Windows 7 or 8), right click any listed HP Photosmart 7520 icon and select Remove Device. Once you are done, you will be guided to unplug the USB and the printer will be connected to your wireless network and will be configured through the network for that PC as well. Click on Convert USB to Wireless and follow the steps to connect the printer to your network.Click the top Utilities tab, then select Printer Setup & Software.From the desktop, go to Start > HP > HP Photosmart 7520 and open the HP Photosmart 7520 software.The easiest way to achieve this method is to convert the current USB into a wireless connection as following: ![]() If so, you may connect the printer to this PC without the USB cable as it is connected to the same network (via a wired network) as the printer will be connected wirelessly. To clarify first, is the primary desktop machine connected to your home router with a wired network cable? (ethernet) What is the best way to add this printer to our wireless network without wireless capability on the main computer? I would like to put the printer on the wireless network without disturbing this set-up. What I would like to do is to leave the main computer set up exactly as it is (USB connection). By the way, I realize that we will need to install the printer drivers on any wireless PCs that we want to have access to the PhotoSmart printer. I want to add wireless functionality so we have both options available (USB-only for the desktop, wireless for the iPhones, iPad tablets and the other computers on the wireless LAN). I do not want to replace USB connectivity with wireless. However, the primary desktop computer does not have wireless connectivity, which is why I connected it to the printer with a USB cable. We also have a wireless network and would like other devices on that network to use the HP printer. I set the printer up via a USB cable to a single computer (the primary desktop machine). ![]() We recently purchased an HP PhotoSmart 7525 all-in-one printer. Business PCs, Workstations and Point of Sale Systems.Printer Wireless, Networking & Internet.DesignJet, Large Format Printers & Digital Press.Printing Errors or Lights & Stuck Print Jobs.Notebook Hardware and Upgrade Questions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |